Stepper Motor Driver

Driver for stepper motor

expand all in page
  • Library:

  • Simscape / Electrical / Electromechanical / Reluctance & Stepper

  • Stepper Motor Driver block

Description

The Stepper Motor Driver block represents a driver for a stepper motor. It creates the pulse trains, A and B, required to control the motor. This block initiates a step each time the voltage at the ENA port rises above the Enable threshold voltage parameter value.

If the voltage at the REV port is less than or equal to the Reverse threshold voltage parameter value, pulse A leads pulse B by 90 degrees. If the voltage at the REV port is greater than the Reverse threshold voltage value, pulse B leads pulse A by 90 degrees and the motor direction is reversed.

At time zero, pulse A is positive and pulse B is negative.

If you set the Stepping mode parameter to Half stepping, the Stepper Motor Driver block can produce the output waveforms required for half stepping. In this mode, there is an intermediate state between the full steps, in which just one of the A or the B half-windings is powered. As a result, the step size is half of the stepper motor’s full step size. At half steps, windings that are not powered are short-circuited. This approximates the effect of a freewheeling diode connected across the windings.

Averaged Mode

If you set the Simulation mode parameter to Averaged, both for a Stepper Motor Driver block and for the Stepper Motor block connected to it, then the individual steps are not simulated. This can be a good way to speed up simulation. The Averaged mode assumes that the external controller provides a step rate demand. This step rate demand is determined from the voltage applied between the ENA and REF ports on the Stepper Motor Driver block, by multiplying this voltage by the value of the Step rate sensitivity parameter. The rotation direction is set by the REF port in the same way as for the Stepping mode.

Averaged mode needs to communicate the step rate demand and also output voltage amplitude information to the Stepper Motor block. To do this, the step rate demand is applied as an equivalent voltage across the A+ and A- ports. Similarly the output voltage amplitude information is conveyed by applying a steady-state voltage across the B+ and B- ports with value equal to the Output voltage amplitude parameter.

Assumptions and Limitations

  • To use Averaged mode, the Stepper Motor Driver block must be directly connected to a Stepper Motor block also running in Averaged mode.

  • When changing from Stepping to Averaged mode and back, you will need to modify your upstream blocks that provide the input voltages to the Stepper Motor Driver block. One way to achieve this easily is to use Simulink® variant subsystems.

Ports

Conserving

expand all

Electrical conserving port associated with the A-phase positive terminal.

Electrical conserving port associated with the A-phase negative terminal.

Electrical conserving port associated with the B-phase positive terminal.

Electrical conserving port associated with the B-phase negative terminal.

Electrical conserving port associated with the step trigger input.

Electrical conserving port associated with the floating reference voltage.

Electrical conserving port associated with the motor direction input.

Parameters

expand all

Use Averaged only if the block is connected directly to a Stepper Motor block also running in Averaged mode.

This parameter converts the voltage presented across the ENA and REF ports into a step rate demand.

Dependencies

To enable this parameter, set Simulation mode to Averaged.

When the voltage at the ENA port rises above this threshold, the Stepper Motor Driver block initiates a step.

Dependencies

To enable this parameter, set Simulation mode to Stepping.

When the voltage at the REV port rises above this threshold, pulse B leads pulse A by 90 degrees, and the motor direction is reversed.

Amplitude of the output pulse trains.

Select Full stepping or Half stepping.

Model Examples

Stepper Motor with Control

Stepper Motor with Control

How to use the Stepper Motor Driver and Stepper Motor blocks together to implement a controlled permanent magnet stepper motor. The model provides two controller options: one to control position and one to control speed. To change the controller type, right-click on the Controller block, select Variant->Override using-> and select Position or Speed.

Stepper Motor Averaged Mode

Stepper Motor Averaged Mode

The Stepper Motor simulating in Stepping and Averaged simulation modes. The purpose of Averaged mode is faster simulation for any loads that do not cause slip. To avoid incorrect interpretation of results, the stepper motor has an approximate detection of slip which can be set to generate a warning or an error.

Extended Capabilities

C/C++ Code Generation
Generate C and C++ code using Simulink® Coder™.

See Also

|

Introduced in R2008a

Simscape Electrical Documentation

Support