SPST Switch

Single-pole single-throw switch

expand all in page
  • Library:

  • Simscape / Electrical / Switches & Breakers

  • SPST Switch block

Description

The SPST Switch block models a single-pole single-throw switch:

  • When the switch is open, port p is connected to port n through a resistance with value equal to the reciprocal of the Open conductance parameter value.

  • When the switch is closed, port p is connected to port n through a resistance with value equal to the Closed resistance parameter value.

If the Threshold width parameter is set to zero, the switch is closed if the voltage presented at the vT control port exceeds the value of the Threshold parameter.

If the Threshold width parameter is greater than zero, then switch conductance G varies smoothly between off-state and on-state values:

G=xRclosed+(1−x)Gopen

λ=vT−ThresholdThreshold width

x={0for λ≤03λ2−2λ3for 0<λ<11for λ≥1

The block uses the function 3λ2 – 2λ3 because its derivative is zero for λ = 0 and λ = 1.

Defining a small positive Threshold width can help solver convergence in some models, particularly if the control port signal vT varies continuously as a function of other network variables. However, defining a nonzero threshold width precludes the solver making use of switched linear optimizations. Therefore, if the rest of your network is switched linear, set Threshold width to zero.

Optionally, you can add a delay between the point at which the voltage at vT passes the threshold and the switch opening or closing. To enable the delay, on the Dynamics tab, set the Model dynamics parameter to Model turn-on and turn-off times.

Modeling Variants

The block provides two modeling variants. To select the desired variant, right-click the block in your model. From the context menu, select Simscape > Block choices, and then one of these variants:

  • PS control port — The block contains a physical signal port that is associated with the threshold voltage. This variant is the default.

  • Electrical control port — The block contains electrical conserving ports that are associated with the threshold voltage.

Ports

Refer to the figure for port locations.

Input

expand all

Physical port associated with the signal that opens and closes the switch.

Dependencies

This port is visible only when Block Choice is set to PS control port.

Conserving

expand all

Electrical conserving port.

Electrical conserving port.

Electrical conserving port for the positive voltage associated with opening and closing the switch.

Dependencies

This port is visible only when Block Choice is set to Electrical control port.

Electrical conserving port for the negative voltage associated with opening and closing the switch.

Dependencies

This port is visible only when Block Choice is set to Electrical control port.

Parameters

expand all

Main

Resistance between the p port and n when the switch is closed. The value must be greater than zero.

Conductance between the p port and n when the switch is open. The value must be greater than zero.

The threshold voltage above which the switch will turn on.

The minimum voltage increase above the threshold value that will move the switch from fully open to fully closed.

Dynamics

Select whether the block models a switching delay:

  • No dynamics — Do not model the delay. This is the default option.

  • Model turn-on and turn-off times — Use additional parameters to model a delay between the point at which the voltage at vT or + and - passes the threshold and the switch opening or closing.

Time between the input voltage exceeding the threshold voltage and the switch closing. The value must be greater than zero.

Dependencies

This parameter is visible only when you select Model turn-on and turn-off times for the Model dynamics parameter.

Time between the input voltage falling below the threshold voltage and the switch opening. The value must be greater than zero.

Dependencies

This parameter is visible only when you select Model turn-on and turn-off times for the Model dynamics parameter.

The value of the physical signal input vT at time zero. This value is used to initialize the delayed control voltage parameter internally.

Dependencies

This parameter is visible only when you select Model turn-on and turn-off times for the Model dynamics parameter.

Model Examples

Custom Solenoid with Magnetic Hysteresis

Custom Solenoid with Magnetic Hysteresis

A limited travel solenoid with return spring. Magnetic hysteresis is modeled using the Reluctance with Hysteresis library block.

Extended Capabilities

C/C++ Code Generation
Generate C and C++ code using Simulink® Coder™.

See Also

| | | |

Topics

Introduced in R2012b

Simscape Electrical Documentation

Support